The first process of water-based wood paint coating is a deployment work。This determines whether the painting is bright and complete，Whether the construction is simple。In order to improve these properties，The following five deployment rules must be followed：
First rule：Polishing adjustment。Water-based wood paint polishing adjustment，This is very important for the entire construction。Just like a transparent putty and a transparent 易彤料理机售后 primer，Good grindinginess is even necessary。Generally，The higher the hardness of the aqueous wood 易彤破壁机漏水维修 lacquer，Relatively speaking Mood is better； The longer the drying time, the better。At the same time, by adjusting the formula or use some scattered slurry，Both can play a role in improving polishing polishing。
Second rule：Adjust the drying speed。Water-based wood lacquer factory construction drying speed is a key factor。Due to the fact that the factory is more compact，After painting, you can't wait.， The drying speed of the coating will directly affect the production efficiency of the plant.。therefore，If aqueous wood paint is replacing oily paint， It must improve drying speed。There are two forming auxiliaries in its formula.。
Compound：One is ethylene glycol butyl ether and dipropylene glycol，The other is 易彤破壁机哪里可以维修 propylene glycol butyl ether and dipropylene glycol methyl ether。Adjust the ratio of two film forming additives appropriately，You can adjust the total amount of drying speed and film formation aid。
Article 3 Rules：Find the balance between flatness。The final step in the production of aqueous wood paint is viscosity adjustment。Viscosity term is called rheological properties。High quality aqueous wood paint must have good leveling performance，It must also have good abdomen。Improve rapidity can reduce unnecessary waste，on the other hand， The hand and gloss of the paint film will be greatly improved。When the viscosity is not enough It will cause the viscosity of the viscosity to affect leveling，therefore， For balance between level and sag， Usually used polyurethane thickeners。Will not affect water resistance，It also improves viscosity and leveling。
Article 4 Rules：Surface modification。Since many shoppers like to use nails or keys to scratch film twice with nails or keys when they judge the paint，See if there is a scratch？therefore， Water-based wood paint must have high hardness and scratch resistance。Single partial water paint to achieve2-3HIs a bit difficult hardness。And it must have good scratch resistance。usually， under these circumstances，Some surface additives can be added to the aqueous wood coating，Make it gradually moved to the surface during the drying process of the paint film，Use its own characteristics and higher hardness to improve the scratch resistance of the paint film。
Article 5 Rules：Increase transparency。The higher the transparency， Silica matte powder determines the balance between transparency and gloss adjustment。 in short，In order to achieve a good aqueous wood paint coating effect，We must master the above five formula adjustment methods。
Water-based wood paint mixing skills
1。 Be careful when mixing aqueous wood coating。Try example first，Preliminary acquisition of the number of matched paints，Then prepare a large sample according to the results of the small sample。the first， Adjust the auxiliary color and auxiliary color in a small container, respectively。
2。 First add the main color（Color in color，Small coloring strength），Then add a strong chromoty to slow and intermittently（Colorless），Continue to stir the color change of the aqueous wood paint at any time。
3。 “From shallow to deep”，Especially when adding pigments with strong columns，Avoid excessive。
4。 The color of the aqueous wood lacquer and dry coating film will be slightly different when matching color.。Film is wet，The color of various coatings is usually shallow，Dry color after dry。therefore，If the sample is dry sample，then，Before performing color measurement comparison，Color matching paints need to be dried。 If the sample is a wet sample，You can put the sample in color matching coatings，Observe if the two colors are the same。
5， Pre-know the floating degree of polychromatic coatings and changes in coating。Especially amino coatings and whole chloride coatings，Need more attention。
6。 During deploying multi-colored aqueous wood lacquers，It is necessary to select the same coatings as the same.，Solvent systems should also be miscible，Apart from this， Due to the solubility of paint，Will affect quality，Stratification Even precipitation or gel，Not available。
7。 Since colors typically have a variety of different colors，If you have a green，Usually use yellow green head and blue yellow head； Blue and red head and red head and blue head should be used when mixing with purple red。 When matching orange，Should use red and yellow head with red head。
8。 Pay attention to mixed aqueous wood lacquer。What auxiliary materials need to be added，For example, dry colors Hardener Diluent and many more，To avoid affecting color。
9。 Mix gray Green and other multicolor coatings，Formulation of a variety of pigments，The density and oil absorption rate of the pigment are different.，“float”with“flowering”It is likely to happen，at this time， Trace surfactants or spacing or antifoulages can be appropriately added。Plus0。1％Silicone oil to control，Various surfactants produced by foreign companies，What solvent system is required to use，The number of adds is usually0。1％?1％。
10。 Use a color paint film slightly transparent，Choosing a suitable base color can make the color of the outer coat better than the original paint color。This is based on natural light reflection and absorption principle，Color generated by superimposing background color and primary colors，Coating project is called“Transparent”。E.g， Yellow primer can make red more bright，Gray primer makes red red，The front blue primer can make black black，Brighten，Water blue primer makes white cleaner。cream， powder， ivory， sky blue，White application as primer。
